Turn any industrial plant into an intelligent energy system in minutes. Detect waste, avoid penalties, comply with grid code. Works with your existing meters. From $5 USD/meter/month.
Utility surcharges up to 120% on your electricity bill. Most plants pay penalties without knowing it. PF 0.97 required from April 2026.
Equipment consuming more than it should. Phase imbalance causing premature failures. You don't see it until the bill arrives.
Grid code requires 8,640 readings/month. Manual monitoring is impossible. One audit can cost more than a year of monitoring.
"A client detected a power factor of 0.82 within the first 24 hours. That single finding was saving them $4,200/month in utility penalties they didn't know they were paying."
Industrial plant, Monterrey, Mexico
From installation to first insights: less than 10 minutes.
What separates Wertek from dashboards.
15 compatible meters from 13 brands. Modbus TCP, Modbus RTU, MQTT 4G/5G.
No vendor lock-in. Works with what you already have.
Every meter becomes the same data model. No more manual mapping, no more spreadsheets.
IAES open standard.
From raw data to decisions: alerts, compliance, and predictive insights.
Intelligence that compounds over time.
Start with monitoring. Grow into intelligence.
Replaces manual meter reading and spreadsheets
Real-time dashboards, smart alerts, historical charts, PDF reports. See your consumption from anywhere.
Built for Codigo de Red and power quality compliance
THD monitoring, voltage balance, power factor tracking, Grid Code compliance reports. Automatic violation alerts.
Detect anomalies before failures happen
Correlate energy patterns with equipment health. Demand optimization. Anomaly detection. Custom ML models.
Same platform. Same dashboards. Same insights.
Works with the most common industrial meters in Mexico and LATAM.
| Marca | Modelo | Conexion | Per-Phase | Bidireccional | THD |
|---|---|---|---|---|---|
| Eastron | SDM630 | Modbus RTU | ✓ | ✓ | ✓ |
| Schneider | PM8000 | Modbus TCP | ✓ | ✓ | ✓ |
| Siemens | PAC3200 | Modbus TCP | ✓ | ✓ | ✓ |
| Carlo Gavazzi | EM340 | Modbus RTU | ✓ | ✓ | ✓ |
| Acrel | ADW300 | MQTT 4G | ✓ | ✓ | ✓ |
Monitor power quality parameters against your country's regulations. Automatic alerts when limits are violated.
Most plants are not actually compliant — they just don't know it.
Connect your PF correction controller via Modbus. Monitor power factor, temperature, step status and alarms in real time. Same gateway, same platform, same price.
Weighted by 5 factors: power factor, temperature, THD, switching rate and accumulated life. One number to know if your bank is healthy.
Low PF, excessive temperature, leakage current, contactor wear. Notifications via email, Telegram or push.
See which steps are active, how many operations each contactor has accumulated, and detect failed steps instantly.
When a bank degrades past thresholds, a work order is created automatically in your CMMS with the full diagnosis.
Power factor target adapts automatically to your country's regulation. Mexico 0.97, Brazil 0.92, USA 0.90. 17 countries built-in.
Works with major PF correction controllers. No matter who made your capacitor bank.
No contracts. No surprises. Cancel anytime.
The gateway software is free. No hardware lock-in. No installation fees. Use your existing meters and capacitor bank controllers.
Everything you need to start. Eastron X96 3-phase meter + Gateway + guided installation. Up to 500 Amp.
Connect your existing Modbus meter with the free Wertek Gateway. No additional hardware needed.
Download GatewayDirect 4G/5G connection. No gateway, no PC, no network configuration. Includes temperature monitoring and leakage current.
Contact SalesConnect your meters. Get insights in minutes.